Project guide

How much floor screed do I need?

A screed is the thick layer that brings a floor up to level. The depth and whether it is bonded, unbonded or floating decide how thick it has to be.

Multiply the floor area by the depth, add 10%, then split a 1:4 mix into cement and sharp sand, or count bags.

Updated Based on manufacturer guidance, sources below

The short answer

A traditional sand and cement screed is typically about 2.2 kg per m² for every millimetre of depth. Add 10%. A 1:4 mix by weight is one part cement to four parts sharp sand. Bagged screed is often a little less, about 1.8 to 2.0 kg per m² per mm. A 10 m² floor at 50mm is about 0.55 m³, 10 bags of cement and about 1 tonne of sharp sand at 1:4.

For a few millimetres only, see self-levelling compound. For bricklaying mortar, see how much mortar.

Work it out for your floor

Change the measurements and the quantities update straight away.

Floor area
10 m²
Volume
0.55 m³ including 10%
Screed
1210 kg at 2.2 kg per m² per mm
Cement, 1:4
10 x 25kg (242 kg)
Sharp sand
0.97 tonnes, about 2 bulk bags

Your list

  • 10Cement 25kg (1:4 by weight)
  • 2Sharp sand, bulk bags
Open this list in SmartBuild

A sand and cement mix opens cement and sharp sand with these quantities. Bagged screed is not on the price list yet, so that choice opens the floor tiling job with your room size. Check the bag or the delivery note.

How the numbers are worked out

The formula

  • Area (m²) = length x width. Volume (m³) = area x depth in metres x 1.1
  • Traditional screed, kilograms = area x depth (mm) x 2.2 x 1.1
  • 1:4 by weight: cement = kilograms / 5, sharp sand = the other four fifths
  • 1:3 uses kilograms / 4 as cement. 1:5 uses kilograms / 6. The range for a traditional mix is 1:3 to 1:5
  • Bagged screed, kilograms = area x depth (mm) x 2.0 x 1.1, then divide by 25kg and round up

Worked example

A 10 m² floor, 50mm thick, plus 10%:

  • Volume: 10 x 0.05 x 1.1 = 0.55 m³
  • Traditional weight at 2.2 kg per m² per mm: 10 x 50 x 2.2 = 1,100 kg, plus 10% = 1,210 kg
  • A 1:4 mix: cement 1,210 / 5 = 242 kg, so 10 x 25kg bags. Sharp sand is 968 kg, about 0.97 tonnes, so 2 bulk bags
  • Bagged screed at 2.0 kg per m² per mm: 10 x 50 x 2.0 x 1.1 = 1,100 kg, so 44 x 25kg bags

Materials checklist

  • CementOrdinary 25kg bags, for a site-mixed screed. Measure by weight for the ratio, or by the same bucket every batch if you are batching by volume and the specification allows it.
  • Sharp sandCoarse sand, not building sand. Building sand is for bricklaying and makes a weak screed.
  • Bagged floor screedA pre-mixed bag, if you would rather not batch sand and cement. Coverage is printed on the bag, often around 1.8 to 2.0 kg per m² per mm.
  • Separating membraneFor an unbonded screed, so the screed can move slightly on the slab.
  • Insulation and edging stripFor a floating screed. The edging lets the screed expand without pushing the walls.

You'll also need

  • A mixer or a screed pump for a large floor
  • Screed rails or battens to set the depth
  • A straight edge, a float and a tamper
  • Polythene to cure the surface
  • Gloves and eye protection: wet cement burns

Step by step

  1. Measure area and depthLength times width, and the depth you will actually lay, in millimetres.
  2. Choose the build-upBonded screeds are the thinnest. Unbonded screeds sit on a membrane. Floating screeds sit on insulation and are the thickest.
  3. Check the minimumTraditional sand and cement is normally at least 25mm bonded (often specified at 40mm), 50mm unbonded and 65mm floating in a house. Bagged products can be thinner. Check the bag.
  4. Work out the weightUse about 2.2 kg per m² per mm for sand and cement, or about 2.0 for bagged screed, then add 10%.
  5. Split a site mixFor 1:4 by weight, one fifth of the kilograms is cement and the rest is sharp sand. Round cement up to 25kg bags and sand up to bulk bags.

Tips from the manufacturers

  • The 2.2 kg per m² per mm figure comes from a ready-mixed screed coverage table of about 9 m² per tonne at 50mm, which is just over 2.2 kg per m² per mm. This page uses 2.2 so the arithmetic stays simple. A delivery can vary slightly. Check the note that comes with it.
  • The Concrete Centre describes a traditional cement-sand screed as 1:3 to 1:5. A 1:4 mix is the usual general-purpose choice. Richer is not always better: it can shrink and crack more.
  • MPA Mortar describes bonded screed as at least 25mm and normally specified at 40mm, unbonded as at least 50mm, and floating as 75mm, with 65mm normally accepted in housing. The Concrete Centre table gives floating screed as at least 65mm for light loads and 75mm for heavier ones, with at least 25mm of cover over heating pipes.
  • Mapei Topcem Pronto, a bagged screed, prints 18 to 20 kg per m² per centimetre, which is 1.8 to 2.0 kg per m² per mm, and allows about 10mm bonded, 35mm unbonded and 55mm floating for that product. This page uses 2.0, the top of that range. Another bag may differ.

Mistakes to avoid

  • Using building sand because it was left over from bricklaying.
  • Laying 25mm over a polythene membrane. An unbonded screed wants about 50mm or it curls and cracks.
  • Forgetting the 10%, and the extra depth where the slab falls away from the door.
  • Covering underfloor heating pipes with less than about 25mm of screed.

Frequently asked questions

How much screed do I need per m²?

At 50mm, a traditional screed is typically about 110 kg per m² before the extra 10%, or about 0.05 m³. Bagged screed at 2.0 kg per m² per mm is 100 kg per m² at 50mm. Check the bag.

How much screed for 10 m² at 50mm?

About 0.55 m³ including 10%. At 1:4 that is about 1,210 kg: 10 bags of cement and about 0.97 tonnes of sharp sand. Bagged screed at 2.0 kg per m² per mm is about 1,100 kg, or 44 bags of 25kg.

What sand and cement ratio is floor screed?

Traditional screed is typically 1:3 to 1:5 cement to sharp sand by weight. A 1:4 mix is the usual general-purpose choice. Use sharp sand, not building sand.

How thick should floor screed be?

For traditional sand and cement, normally at least 25mm bonded, 50mm unbonded and 65mm floating in a house. Specifiers often call for 40mm bonded and 75mm where the floor is heavily loaded or has heating pipes. Bagged screeds can be thinner. Check the product.

Is bagged screed the same weight as sand and cement?

Not exactly. A typical bagged screed is about 1.8 to 2.0 kg per m² per mm. A traditional ready-mixed screed coverage table is a little higher, about 2.2. Use the figure for the one you are laying.

Sources

Quantities are estimates for typical jobs, using the coverage figures above. Products vary, so check the data sheet for the product you buy, and talk to a professional for structural, electrical or gas work. SmartBuild is independent and not affiliated with any of the manufacturers listed.

Get the full priced list

Open SmartBuild with your measurements and see a total from up-to-date prices where we have them, plus links to check other suppliers. Free, no sign-up needed for DIY.

Open in SmartBuild