Project guide

How much self-levelling compound do I need?

Depth matters more than the brand. A millimetre or two across a whole room is a bag you did not expect.

Allow about 1.6 kg per square metre for every millimetre of depth, then add 10% if the floor is uneven.

Updated Based on manufacturer guidance, sources below

The short answer

Kilograms = area x depth in millimetres x about 1.6, then add 10%. Published rates are typically about 1.4 to 1.7 kg per m² per mm. A 4 x 3m room at 3mm is 12 m², so about 63 kg, which is 3 bags of 25kg.

If the floor needs a full screed rather than a few millimetres, see how much floor screed. After it is level, see laminate flooring or floor tiles.

Work it out for your floor

Change the measurements and the quantities update straight away.

The depth you will actually pour, not the deepest hole on its own.
Floor area
12 m²
Depth
3 mm at 1.6 kg per m² per mm
Compound
63.4 kg including 10%
Bags
3 x 25kg

Your list

  • 3Bags of self-levelling compound, 25kg (about 63.4 kg)

The rate is for a flat floor. A hollow or a slope needs more than the average depth. Check the bag.

Open the floor list

Self-levelling compound is not a separate job yet. This opens the laminate flooring list, or the floor tiling list, with your room size. Buy the compound from the figure above and check the bag.

How the numbers are worked out

The formula

  • Area (m²) = length x width
  • Kilograms = area x depth (mm) x rate, then x 1.1
  • Rate is typically about 1.6 kg per m² per mm. Published sheets run from about 1.4 to about 1.7
  • Bags = kilograms / bag size (often 20kg or 25kg), rounded up

Worked example

A 4 x 3m room, averaged at 3mm, at 1.6 kg per m² per mm:

  • Area: 4 x 3 = 12 m²
  • Before the extra: 12 x 3 x 1.6 = 57.6 kg
  • With 10%: 57.6 x 1.1 = 63.4 kg
  • Bags: 3 x 25kg, or 4 x 20kg

At the low end of published rates (1.4) the same floor is about 55 kg plus the same 10%. At the high end (1.7) it is about 67 kg. Check the bag.

Materials checklist

  • Self-levelling compoundA cement-based powder you mix with water and pour. It finds a level. It is not a wearing surface unless the bag says so.
  • PrimerMost bags want a primer so the compound does not dry too fast or fail to bond. Use the primer the same maker names.
  • Edging foam or sealantStops the wet mix running under the skirting and into the next room.

You'll also need

  • A spiked roller or a smoothing trowel, if the bag asks for one
  • A bucket, a mixer and a measure for the water
  • A depth gauge or a few screws set to the finished level
  • Something to stop the mix at doorways

Step by step

  1. Find the depthSet a straight edge or a laser across the room and measure the gaps. Use the average depth you will pour, and note the deepest spot.
  2. Check the minimumMany compounds will not flow or level below 2 or 3mm, and timber floors often need at least 3mm. A deep hole may need a repair mortar first.
  3. Read the rate on the bagTypical published rates are about 1.4 to 1.7 kg per m² for every millimetre. This page uses 1.6 unless you choose another.
  4. Add 10% and round upThe printed rate is for a flat floor. An uneven floor uses more, which is what the 10% is for.
  5. Prime, pour and leave itFollow the water dose on the bag. Too much water weakens the floor. Keep off it until the bag says you can walk on it.

Tips from the manufacturers

  • Mapei Ultraplan prints 1.6 kg per m² per mm. ARDEX K 15 prints about 1.4 kg of powder per m² per mm, and says to allow more where the floor is rough. BAL Level Max prints about 5 m² at 3mm from a 25kg bag, which is about 1.7 kg per m² per mm.
  • Those three sheets do not agree, so the calculator lets you pick 1.4, 1.6 or 1.7. If your bag prints a different rate, use that.
  • Water is part of the mix, but coverage is given for the powder in the bag. Do not add the water on top of the kilogram figure.
  • A compound is for millimetres. If you need 40 or 50mm to bring a floor up, that is a screed, not a bucket of leveller. Some fibre levellers can go deeper: the BAL Level Max sheet allows a thick bed, but only as that product describes.

Mistakes to avoid

  • Measuring only the deepest hole and ordering that depth for the whole room, or measuring only the high spot and running out.
  • Skipping the primer, then watching the compound dry in patches and crack.
  • Adding extra water to make it flow further. It covers more and then fails.
  • Pouring it against a doorway with nothing to hold it, and levelling the hall as well.

Frequently asked questions

How much self-levelling compound do I need per m²?

Typically about 1.6 kg per m² for every millimetre of depth. At 3mm that is about 4.8 kg per m² before the extra 10%. Published rates are about 1.4 to 1.7 kg per m² per mm. Check the bag.

How many bags for a 12 m² room at 3mm?

At 1.6 kg per m² per mm, 12 x 3 x 1.6 is 57.6 kg, or about 63 kg with 10% extra. That is 3 bags of 25kg, or 4 bags of 20kg.

Is self-levelling compound the same as screed?

No. Compound is a thin, pourable leveller, usually a few millimetres. A sand and cement screed is a much thicker layer, often 50mm or more when it is not bonded to the slab.

Do I add 10%?

Yes if the floor is not flat, which is why you are levelling it. The rate on the bag assumes a flat surface. The 10% is a modest allowance, not a substitute for measuring the depth.

Can I use it on floorboards?

Only if the bag says so, and usually at a greater minimum depth than on concrete, often with a primer and a mesh. A bouncy floor needs boarding first, not a thicker pour.

Sources

Quantities are estimates for typical jobs, using the coverage figures above. Products vary, so check the data sheet for the product you buy, and talk to a professional for structural, electrical or gas work. SmartBuild is independent and not affiliated with any of the manufacturers listed.

Get the full priced list

Open SmartBuild with your measurements and see a total from up-to-date prices where we have them, plus links to check other suppliers. Free, no sign-up needed for DIY.

Open in SmartBuild