Project guide
How much mortar do I need for brickwork and blockwork?
Count the wall, turn it into mortar, then split that into cement and building sand. Blockwork uses much less mortar than brickwork, because there are fewer joints.
A half-brick wall typically needs about 0.03 cubic metres of mortar per square metre, which is about 0.55 cubic metres per 1,000 bricks with 10% extra.
The short answer
Allow about 0.03 m³ of mortar per m² of half-brick wall, and about 0.012 m³ per m² of 100mm blockwork, then add 10%. A 1:4 mix is about 14 x 25kg bags of cement and 1.5 tonnes of building sand per m³. Per 1,000 bricks that is about 0.55 m³ including 10%: 8 bags of cement and about 0.83 tonnes of sand.
For the brick count, see how many bricks. For blocks, see how many concrete blocks. The same cement and sand sums are on how much sand and cement.
How the numbers are worked out
The formula
- Half-brick wall: about 60 standard bricks per m², and about 0.03 m³ of mortar per m²
- 100mm blocks: about 10 blocks per m² (440 x 215mm face), and about 0.012 m³ of mortar per m²
- Mortar (m³) = area x the rate above x 1.1
- Per 1,000 bricks: 1,000 / 60 x 0.03 x 1.1 = about 0.55 m³
- Cement (25kg bags) at 1:4 = m³ x 14. Building sand (tonnes) = m³ x 1.5
- Other mixes: about 19 bags per m³ at 1:3, 12 at 1:5 and 10 at 1:6. Sand stays about 1.5 tonnes
Worked example
A half-brick wall of 10 m², 1:4 mix, with 10% extra mortar:
- Bricks: 10 x 60 = 600, plus 5% = 630 bricks
- Mortar: 10 x 0.03 x 1.1 = 0.33 m³
- Cement: 0.33 x 14 = 4.6, so 5 x 25kg bags
- Building sand: 0.33 x 1.5 = 0.50 tonnes, so 1 bulk bag
The same mix for 1,000 bricks (about 16.7 m²) is 0.55 m³ including 10%: 8 bags of cement and about 0.83 tonnes of building sand.
Materials checklist
- CementGeneral-purpose cement in 25kg bags.
- Building sandSoft sand for brick and block mortar. Sharp sand is for screed and slab beds, and it makes a harsh bricklaying mortar.
- Mortar plasticiserAn air-entraining plasticiser, dosed as the bottle says, in place of lime. Do not add it to masonry cement that already has one.
- Bricks or blocksAbout 60 bricks or 10 blocks per m², plus 5% for cuts and breakages.
You'll also need
- A mixer or a mixing tub, a shovel and buckets
- A brick trowel, a pointing trowel and a jointer
- A spirit level, a string line and pins
- Gloves and goggles: wet cement burns skin
Step by step
- Measure the face of the wallLength times height, in metres. Take off doors and windows. A one-brick (215mm) wall needs about twice the mortar of a half-brick wall, so enter twice the area.
- Or count the bricksDivide the number of bricks by 60 to get the area of a half-brick wall. Divide blocks by 10.
- Turn the area into mortarMultiply by 0.03 for half-brick work or 0.012 for 100mm blocks, then by 1.1.
- Choose the mix1:4 suits most walls. Use 1:3 below the damp-proof course or in a very exposed spot, and a weaker mix on soft older bricks.
- Split into bagsAt 1:4, about 14 bags of cement and 1.5 tonnes of building sand per cubic metre. Round up.
Tips from the manufacturers
- The 0.03 m³ per m² and 0.012 m³ per m² rates are the same allowances used for the brick, block and sand guides. They sit a little above the bare volume of a 10mm joint, so there is mortar for the trowel as well as the wall. The extra 10% is on top.
- Sixty bricks per m² is the standard UK brick (215 x 102.5 x 65mm) in stretcher bond with 10mm joints. One thousand bricks is 1,000 / 60 = 16.7 m², and 16.7 x 0.03 x 1.1 is 0.55 m³.
- The Brick Development Association says a good building sand should be used, and that one tonne of ready-mixed lime:sand, gauged with cement on site, generally lays about 1,000 bricks. That is a different product from a site-mixed 1:4. The sand in this 0.55 m³ is about 0.83 tonnes, in the same region, with the cement counted separately.
- Follow the dose on the plasticiser. Too much makes the joints porous. Do not add a plasticiser to masonry cement, which already contains one.
Mistakes to avoid
- Ordering mortar for the face area of a one-brick wall and getting halfway round.
- Using sharp sand left over from a screed. It is hard to spread and hard to point.
- Mixing a stronger mortar than the bricks. Soft or older bricks can crack around a 1:3 joint.
- Mixing more than you can lay in about an hour. Mortar that has started to set should not be knocked back up with water.
Frequently asked questions
How much mortar do I need per m² of brickwork?
About 0.03 m³ per m² of half-brick wall, before the extra 10%. With 10% that is 0.033 m³, about half a 25kg bag of cement and about 50 kg of building sand at a 1:4 mix.
How much mortar do I need for 1,000 bricks?
About 0.55 m³ including 10%, for standard bricks with 10mm joints in a half-brick wall. At 1:4 that is 8 bags of cement and about 0.83 tonnes of building sand.
How much mortar do I need for blockwork?
About 0.012 m³ per m² for 100mm blocks with 10mm joints, plus 10%. Ten square metres is about 0.13 m³: 2 bags of cement and about 0.2 tonnes of building sand at 1:4. One hundred blocks is the same, because they cover 10 m².
What mortar mix should I use for bricks?
A 1:4 cement to building sand mix suits most general brickwork. Use about 1:3 below the damp-proof course or in a very exposed wall, and 1:5 or 1:6 where the bricks are soft.
Is this the same as floor screed?
No. Bricklaying mortar uses building sand. Floor screed uses sharp sand, and much more of it, because the layer is thick. See the floor screed guide for that sum.
Sources
- ConcreteMath material quantity tables
- Brick Development Association: mortar for brickwork (building sand, and about 1 tonne of gauged lime:sand per 1,000 bricks)
Quantities are estimates for typical jobs, using the coverage figures above. Products vary, so check the data sheet for the product you buy, and talk to a professional for structural, electrical or gas work. SmartBuild is independent and not affiliated with any of the manufacturers listed.
Related guides
Get the full priced list
Open SmartBuild with your measurements and see a total from up-to-date prices where we have them, plus links to check other suppliers. Free, no sign-up needed for DIY.