Project guide

How much tile adhesive do I need?

The bag rate depends on the trowel notch, not on a single number for every tile. Tile size is what tells you which notch to use.

A floor typically needs about 3.8 kg of adhesive per square metre with a 10mm solid-bed trowel, plus 10%.

Updated Based on manufacturer guidance, sources below

The short answer

Allow about 3.8 kg per m² on a floor (a 10mm solid-bed trowel), about 2 kg per m² on a dry wall (a 6mm notch) and about 2.5 kg per m² on a wet wall (a 6mm solid bed). Add 10%, then round up to 20kg bags. A 4 x 2.5m floor is 10 m², so about 42 kg, which is 3 bags.

For the tiles themselves, see how many tiles you need. For the joints, see how much grout.

Work it out for your tiles

Change the measurements and the quantities update straight away.

Area
10 m²
Typical use
3.8 kg per m² before the extra 10%
Adhesive
42.3 kg including 10%
20kg bags
3

Your list

  • 3Flexible tile adhesive, 20kg bags (about 42.3 kg)

Coverage on the data sheet is for a reasonably flat surface and the trowel named above. A bumpy wall or back-buttered large tile uses more. Check the bag.

Open the tiling list

Opens the floor tiling job for a floor, or the wall tiling job for a wall, with your size filled in. The wall job allows for a solid bed, so its bag count can be higher than a dry-wall 6mm notch. Check the bag.

How the numbers are worked out

The formula

  • Area (m²) = length x width
  • Dry wall, tiles up to 300mm, 6mm notch: about 0.5 m² per kg (about 2 kg per m²)
  • Wet wall, 6mm solid bed: about 0.4 m² per kg (about 2.5 kg per m²)
  • Floors, exteriors or large tiles, 10mm solid bed: about 0.26 m² per kg (about 3.8 kg per m²)
  • Mosaics up to 100mm, dry wall, 4mm notch: about 0.6 m² per kg (about 1.7 kg per m²)
  • Kilograms = area / m² per kg, then x 1.1. Bags of 20kg = kilograms / 20, rounded up

Worked example

A 4 x 2.5m floor, 10mm solid-bed trowel:

  • Area: 4 x 2.5 = 10 m²
  • Before the extra: 10 / 0.26 = 38.5 kg (about 3.8 kg per m²)
  • With 10%: 38.5 x 1.1 = 42.3 kg
  • Bags: 42.3 / 20 = 2.1, so 3 x 20kg bags

The same 10 m² as a dry wall with a 6mm notch is 10 / 0.5 x 1.1 = 22 kg, so 2 bags.

Materials checklist

  • Flexible cement-based adhesiveFor floors, wet rooms, porcelain and underfloor heating. Sold in 20kg bags. A ready-mixed tub is only for small dry walls, if the tub says so.
  • Notched trowel4mm for mosaics, 6mm for most wall tiles, 10mm solid bed for floors and outside. Use the notch the data sheet names.
  • PrimerIf the bag asks for one on plaster, plasterboard, timber or an old tiled floor.

You'll also need

  • Tile spacers or a levelling system
  • A mixer and a clean bucket
  • A sponge and a margin trowel
  • Knee pads on a floor

Step by step

  1. Measure the areaLength times width for a floor, or width times tiled height for a wall. Take off a large window, not every socket.
  2. Match the trowel to the tileSmall mosaics on a dry wall use a 4mm notch. Ordinary wall tiles use 6mm, and a solid bed in a shower. Floors, outside and large tiles use a 10mm solid bed.
  3. Read the coverageDivide the area by the m² per kg for that notch. The figures here are typical for a flexible cement adhesive.
  4. Add 10% and round upMultiply by 1.1 and round up to whole 20kg bags. A bumpy wall needs more than 10%.
  5. Check the bagSpread a small area first. If the ribs do not collapse to a solid bed where the sheet asks for one, use a larger notch.

Tips from the manufacturers

  • These rates are the ones printed for a flexible rapid-set adhesive: 0.6, 0.5, 0.4 and 0.26 m² per kg. The sheet says they may vary with the surface and the trowel.
  • Tiles over about 300mm, and any tile on a floor, should be back-buttered as well as combed onto the wall or floor, so the bed is solid. That uses more adhesive than the notch alone.
  • A 6mm notch does not leave a 6mm bed. The ribs squash down as you bed the tile. Do not build the bed up to fill a hollow floor: level the floor first.
  • Keep the notches the same way, usually in straight lines, so air can escape as you bed the tile.

Mistakes to avoid

  • Buying one bag for a floor because a wall of the same size only needed one.
  • Dotting adhesive on the back of a tile. Voids crack, and in a shower they hold water.
  • Using a ready-mixed tub on a floor or in a shower when the tub says dry walls only.
  • Tiling over a hollow or a slope and hoping a thick bed will hide it.

Frequently asked questions

How much tile adhesive do I need per m²?

Typically about 2 kg per m² on a dry wall with a 6mm notch, about 2.5 kg per m² for a solid bed on a wet wall, and about 3.8 kg per m² on a floor with a 10mm solid-bed trowel. Add 10% and check the bag.

How much adhesive for a 10 m² floor?

At about 3.8 kg per m², 10 m² is about 38 kg, or about 42 kg with 10% extra. That is 3 bags of 20kg.

What trowel notch should I use?

For this type of adhesive, a 4mm notch for mosaics up to 100mm on a dry wall, a 6mm notch for wall tiles up to 300mm (a solid bed in the wet), and a 10mm solid-bed trowel for floors, outside and larger tiles.

Does tile size change how much adhesive I need?

It changes the notch you should use, and the notch sets the coverage. Large tiles are also back-buttered, which uses more. There is no separate kilogram figure for every tile size.

How many m² does a 20kg bag of tile adhesive cover?

On these typical rates, about 12 m² with a 4mm notch, 10 m² with a 6mm notch on a dry wall, 8 m² with a 6mm solid bed, and about 5.2 m² on a floor. That is before the extra 10%, and before a bumpy surface.

Sources

Quantities are estimates for typical jobs, using the coverage figures above. Products vary, so check the data sheet for the product you buy, and talk to a professional for structural, electrical or gas work. SmartBuild is independent and not affiliated with any of the manufacturers listed.

Get the full priced list

Open SmartBuild with your measurements and see a total from up-to-date prices where we have them, plus links to check other suppliers. Free, no sign-up needed for DIY.

Open in SmartBuild