Project guide
How much grout do I need?
Small tiles and wide joints use much more grout than large tiles with narrow joints. The sum is the same one manufacturers print on the bag.
Grout depends on the tile size, the joint width and the joint depth. Add 10%, then check the bag.
The short answer
Kilograms per m² = (tile length + tile width) / (length x width) x joint width x joint depth x 1.6, with every measurement in millimetres. Add 10%. A 10 m² floor of 300 x 300 x 8mm tiles with 3mm joints needs about 2.8 kg, so one 5kg bag.
For the adhesive, see how much tile adhesive. For the tiles, see how many tiles.
How the numbers are worked out
The formula
- Area (m²) = length x width
- Kilograms per m² = (length + width) / (length x width) x joint width x joint depth x 1.6
- Tile size, joint width and joint depth are all in millimetres
- 1.6 is a typical weight, in kilograms, of one litre of mixed cement grout
- Kilograms to buy = area x kilograms per m² x 1.1, then round up to a bag (often 5kg)
Worked example
10 m² of 300 x 300mm tiles, 8mm thick, with a 3mm joint:
- (300 + 300) / (300 x 300) = 0.00667
- 0.00667 x 3 x 8 x 1.6 = 0.26 kg per m²
- 10 m² is 2.6 kg, plus 10% = 2.8 kg
- That is 1 x 5kg bag
The same sum for 600 x 300 x 8mm tiles and a 3mm joint is about 0.19 kg per m², so 6 m² plus 10% is about 1.3 kg.
Materials checklist
- Cement-based groutFor most wall and floor tiles. Pick a fine joint grout for narrow joints and a wide-joint grout if the bag says the joint is too wide for the fine one.
- Flexible groutWorth it on timber floors, underfloor heating and anywhere the background moves.
- SpacersThey set the joint width you used in the sum. Take them out before the grout goes in, unless they are the sort made to stay.
You'll also need
- A grout float and a grouting sponge
- Two buckets, one for mixing and one for rinsing
- A mixer for a whole bag, or a small paddle for a cupful
- Silicone for the corners and the joint against a bath or worktop
Step by step
- Measure the tiles and the jointLength and width of the tile, the spacer width, and the thickness of the tile. Use millimetres.
- Work out one square metreAdd the two sides, divide by the tile area, then multiply by the joint width, the depth and 1.6.
- Multiply by the areaThen add 10% for joints that are a little deep, or for what stays on the float and the sponge.
- Round up to a bagGrout is often sold in 5kg bags. A small splashback still needs a bag, because you cannot buy 300 grams.
- Mix only what you can useCement grout starts to stiffen in about an hour. Mix a smaller batch on a small wall.
Tips from the manufacturers
- The 1.6 in the sum is a typical weight for one litre of mixed cement grout, and it is the figure the tiling jobs on SmartBuild already use. The printed table on some bags, including BAL Grout, works out nearer 1.4 kg per litre, so this page is slightly on the safe side of that table.
- BAL Grout's data sheet gives about 2.65 m² per kg for a 200 x 100 x 6mm tile with a 3mm joint, which is about 0.38 kg per m². The same tile on the 1.6 figure is about 0.43 kg per m² before the extra 10%.
- Joint depth is the tile thickness when the joint is full. Do not include the adhesive bed.
- Do not grout the corner, or the gap where tiles meet a bath, basin or worktop. Those joints need silicone, so they can move.
Mistakes to avoid
- Using the same kilogram figure for 100mm mosaics and 600mm floor tiles. Mosaics can use several times more grout.
- Guessing the joint depth. A 10mm porcelain tile needs more than a 6mm ceramic one.
- Mixing a whole 5kg bag for a splashback and having it go off in the bucket.
- Leaving spacers in, then grouting over them, which leaves a stain and a weak spot.
Frequently asked questions
How much grout do I need per m²?
There is no single figure. For 300 x 300 x 8mm tiles with a 3mm joint it is about 0.26 kg per m², before 10% extra. Smaller tiles and wider joints need more.
How much grout for 10 m²?
For 300 x 300 x 8mm tiles and a 3mm joint, about 2.6 kg, or about 2.8 kg with 10% extra. One 5kg bag is enough. A floor of 100mm mosaics can need a bag or more per few square metres.
What does the 1.6 in the grout formula mean?
It is a typical weight, in kilograms, of one litre of mixed cement grout. Some data sheets use about 1.4 and some use more. Check the table on the bag and use that if it differs.
Should the joint depth be the tile thickness?
Yes, when you fill the joint. Grout does not fill the adhesive under the tile, so do not add the bed thickness.
Do I grout the corners?
No. Use sanitary silicone in internal corners and where tiles meet a bath, basin or worktop. Grout there cracks as the joint moves.
Sources
Quantities are estimates for typical jobs, using the coverage figures above. Products vary, so check the data sheet for the product you buy, and talk to a professional for structural, electrical or gas work. SmartBuild is independent and not affiliated with any of the manufacturers listed.
Related guides
Get the full priced list
Open SmartBuild with your measurements and see a total from up-to-date prices where we have them, plus links to check other suppliers. Free, no sign-up needed for DIY.